When a retail shelf looks too dark, adding more watts is not the only option to evaluate. First check where the light is going. A light bar can be visibly illuminated while the merchandise receives uneven coverage because its emitting direction does not suit the shelf layout.
For shelf and display fixture manufacturers, a useful starting point is the relationship between the LED bar, the underside of the shelf and the products below. This article focuses on that relationship, using an iPixel project in which a flat-emitting rigid bar was replaced with a single-sided, angled-emitting design.
1. Identify the area that needs better illumination
Separate the customer's overall impression of brightness from the location of the problem. Is the front of the merchandise difficult to see? Is one part of the shelf bright while another is shaded? Does the empty shelf look acceptable but become uneven after products are placed on it?
Review the shelf with representative products in their intended positions. Record the light-bar location, shelf depth, spacing between levels and the surfaces that need illumination. These observations help determine whether the next sample should change light direction, mounting position, output or a combination of factors.
2. Match the emitting direction to the shelf
A flat-emitting bar and an angled-emitting bar direct their light differently relative to the mounting surface. Beneath a shelf, an angled LED board can aim the output toward the merchandise instead of retaining the same emitting orientation as a flat board.
This does not mean that an angled bar is always better. Its suitability depends on where it is mounted, which way it faces, the shelf geometry and the merchandise arrangement. Confirm the direction in a physical sample before approving the design.
Product structure reference: the LED board is inclined inside a 16 × 16 mm profile. This is a single-sided emitting design, not a dual-sided V-shaped light.
3. Project example: changing the light direction beneath retail shelves
The reported problem
In a retail shelf lighting project, the customer found the illumination from the previous flat-emitting rigid LED bars insufficient. The lights were installed beneath the shelves to illuminate the merchandise on the level below.
The change
iPixel replaced the flat-emitting bars with the 16 × 16 mm angled-emitting design identified for the project as B016120BB1LZ. The inclined internal board changed the emitting direction so the light could be directed across the merchandise area. The bar emits from one side; it does not have two simultaneously illuminated faces.
The outcome and its limits
According to the project information supplied by iPixel, the revised arrangement provided more even coverage and resolved the customer's brightness concern. The customer was satisfied, and the project entered mass production.
No numerical before-and-after illuminance or uniformity measurements are available for this article. The result is reported project feedback, rather than a quantified performance comparison. The available information also does not establish equal power consumption between the previous and replacement lights.
![]()
Final installation photograph supplied for the project. This photograph is not a matched before-and-after measurement.
![]()
Under-shelf installation detail supplied with the project materials.
4. Product reference: keep series specifications separate from the installed configuration
The supplied B016120BB1LZ datasheet lists the following specifications. They describe the product reference; the selected project length and color temperature have not been documented in the available materials.
| Item | Datasheet information |
|---|---|
| Model | B016120BB1LZ |
| Supply | 12 V DC |
| Rated power per metre | 10 W/m |
| LED type | SMD2835 |
| Profile cross-section | 16 × 16 mm |
| Listed reference size | 200 × 16 × 16 mm; custom lengths available |
| CCT options | 3000 K / 4000 K / 6500 K |
| Color rendering | Ra 90 |
| Listed beam angle | 120° |
| Ingress protection | IP20 |
| Mounting feature | Magnetic strip on the back for suitable metal surfaces |
The listed 120° beam angle is not the inclination angle of the LED board. IP20 should not be presented as waterproof protection.
5. Review the sample in the loaded shelf
Use the intended mounting location and representative merchandise when reviewing the revised light. Check coverage across the shelf, the visibility of product fronts, shadows from tall packages and whether the light source is uncomfortable to view from normal shopper positions.
If numerical comparison is required, agree on a measurement plane and fixed measurement points. Keep product placement, supply conditions and treatment of ambient light consistent. Record the readings and agree on the uniformity calculation and acceptance criteria before making a performance claim. Ordinary site photographs support an installation description but do not replace that measurement process.
For this project, the available site photographs show different merchandise areas and viewpoints. They should be used individually to illustrate the supplied application, not as a controlled before-and-after pair.
6. Prepare a useful shelf-lighting inquiry
- Shelf drawing or photographs, including depth and spacing between levels.
- Proposed mounting location and the direction the light needs to face.
- Representative merchandise and the areas that currently appear too dark.
- Available voltage, cable route and connection requirements.
- Required length, color appearance and any agreed optical acceptance criteria.
Discuss your shelf lighting layout
Send your shelf drawing, installation photographs and description of the lighting problem to inquiry@ipixelleds.com. iPixel can review whether an angled rigid bar or another configuration is suitable for sample evaluation.